VersaBase is MIRO-CG's non-penetrating rooftop base for building strut frames. Each base sits on the roof surface, spreads the load, and holds standard strut, so you can assemble a support frame for ductwork, piping, conduit, or mechanical units without fasteners through the roof. VersaBase comes in 12x12 and 18x18 sizes, as a base alone, a base with a strut bracket, or a two-base frame assembly kit.
What You Can Build with VersaBase
Because VersaBase works with standard strut, one base can support many kinds of rooftop frames:
-
Duct and pipe frames, including trapeze-style supports
-
Conduit and cable tray supports
-
Mechanical unit and HVAC unit frames
-
Roller assemblies for piping
The 18x18 base's bracket works with most 90-degree strut brackets, standard or back-to-back strut (vertical or horizontal), and MIRO strut brackets and roller assemblies.

12x12 or 18x18: Choosing the Right VersaBase
The main difference is load. The 18x18 base spreads weight over a larger area, so it carries more at the same roof pressure.
|
12x12 VersaBase |
18x18 VersaBase |
|
|---|---|---|
|
Base size |
12" x 12" x 2" H |
18" x 18" x 2” H |
|
Height to top of bracket |
6" (7/8" bracket) |
6" (volcano bracket) |
|
Strut fit |
7/8" or 1-5/8" strut, depending on bracket |
1-5/8" x 1-5/8" strut |
|
Base material |
UV-resistant ASA |
UV-resistant ASA |
|
Suggested load per base at 2.0 PSI |
216 lbs |
480 lbs |
|
Suggested load per base at 3.0 PSI |
324 lbs |
780 lbs |
|
Suggested load per base at 5.0 PSI |
540 lbs |
1,200 lbs |
|
Matching rubber pad |
12x12 Fitted Rubber Pad |
18x18 Rubber Support Pad |
For the 12x12 base, MIRO-CG recommends system loading that does not exceed 3.0 PSI, or 324 lbs per base.
Base, Bracket or Full Kit
Each size comes in three forms:
-
Base only: the 12x12 VersaBase or 18x18 VersaBase base foot, for use with your own brackets.
-
Base with strut bracket: the 12x12 base with a 7/8" or 1-5/8" strut bracket, or the 18x18 base with a galvanized steel volcano bracket.
-
Frame assembly kit: two bases with strut brackets, two corner brackets, and eight strut nuts with bolts. It's available as a 12x12 7/8" kit, a 12x12 1-5/8" kit or an 18x18 kit.
Each kit's product page links to a detail sheet.
Protecting the Roof and Checking Loads
VersaBase doesn't penetrate the roof, and its wide base spreads the frame's weight to help protect the membrane. Two steps help it do that well:
-
Add a rubber pad. The optional 18x18 Rubber Support Pad is heat-molded from 100% recycled rubber and is UV-resistant. It isolates the base and reduces movement, with a small lip that holds the base in place and holes for venting and drainage. A fitted pad is also available for the 12x12 base.
-
Stay within the suggested loads. Divide the total weight of the frame and what it carries by the number of bases, and keep each base within the load table above. Consult the roofing manufacturer or a qualified structural engineer for guidance on proper load distribution and installation requirements. For detailed load calculations or additional technical assistance, contact MIRO Industries at 800-768-6978.
Shop VersaBase
Browse the full VersaBase line in MIRO-CG's Base Only collection, or contact MIRO-CG for help choosing the right base for your project.
